Operations Manual For Rosengrens Locks

  

How to Operate Your Safe 1. Karma Motif Software. Installing/Replacing the Batteries Remove the battery cover plate and install the four 1.5V (size AA) alkaline batteries. Ensure that the (+) and (-) positions are correct. (If your safe has a round V-3 electronic lock, turn it to the left and pull the panel.

Operations Manual For Rosengrens Locks

Be careful not to damage the cables by pulling the panel too forcefully.) When installing or replacing the batteries, the LCD display will automatically scan the status of the electronic lock system. If everything is fine, the word 'good' will be displayed. The safe is now ready to be used! When the battery is low, 'Lo-bAt' will be seen on the LCD display each time that the START button is pressed.

You should replace the batteries Immediately. Opening the Door Step 1. Push the START button on the control panel. The LCD display will show '------'. Enter 1-2-3-4-5-6, or 5-6-7-8-9-0 which has been programmed at the factory. After pressing the 6 numbers, the LCD display will say 'Open', a green light will come on, and you will hear a beep. Turn the handle clockwise before the word 'Open' disappears.

(Turn the key first before you turn the handle if your safe has a key.)! CAUTION When an incorrect code is entered, the LCD display will display 'Error' and you will hear a beep. Try the right code again after the word 'Error' disappears. HOW TO INPUT YOUR OWN PERSONAL CODES The safe can be programmed with two personal codes. After opening the safe, you should program two codes of your own to take the place of the two factory-preset codes, which are 1-2-3-4-5-6 and 5-6-7-8-9-0.! CAUTION Do not close the safe until a new code has been entered.

Shareaza Free Download For Mobile. Try the new code before locking the safe. Programming the First Code Step 1. After opening the door, find the white memory button. Press the START button on the control panel. The LCD display will show '------'. Enter your 6—digit code (For example, 7-7-7-7-7-7).

May 22, 2017. Operations Manual For Rosengrens: full version free software download. Install Corel Videostudio Pro X6 Vn Zoom Manual Activation key. Keypad #LG3000 Combogard 39E Springbolt Lock #LG6034U02U-00-00 Keypad allows manual. For Hooked Stem Rosengrens Screw-In-Bow Key Stem for RKL Lock.

Press the memory button and make sure that the LCD display shows 'In' and that you hear a beep. Test the new code with the door open. If the new code does not work, repeat the above steps. Programming the Second Code Step 1.

After opening the door, press the memory button. The LCD display will show '-----' (flashing). Press the START button and enter your new code (for example, 8-8-8-8-8-8).

Make sure that the LCD display shows 'In' and that you hear a beep. Test the new code with the door open.

If the new code does not work, repeat the above steps. TIP If you want to use just one personal code, input the same 6-dlgit code both times. Please ensure that you do this in order, following the instructions for programming the first code and then the instructions for programming the second code.

For example, when you want to program 1,3,1,3,1,3, Start - 1,3,1,3,1,3 - Memory button ->Check if it works. Memory button - Start - 1,3,1,3,1,3 ->Check if it works. TROUBLE SHOOTING • The display shows 'Error' and there is a constant buzzing sound. • If the incorrect code is entered 5 times in a row, the display will show 'Error', the red light will illuminate, and the a series of quick beeps will sound for approximately 3 minutes. The correct code cannot be entered until after this 3-minute delay. Try the correct code after the 3 minutes of short series of beeps stop. • You follow the opening procedure but cannot open the safe.

• The green light comes on and the word 'Open' Is displayed, but the door will not open. • The safe repeats self-testing! • The e-lock seems to be dead! • Check if the batteries were inserted properly, or try changing batteries to new ones. Alkaline batteries are strongly suggested.

• Can't key in any code. • 1) Please check if the alarm is ringing with error sign at the LCD window.

If so, please see question #1. • 2) Humidity can harm the electronic systems. Please check if the surroundings has been humid, or someone wiped out the safe with water or any liquid detergent. Even you didn't clean the electronic lock itself, the liquid detergent can flow into the lock system along the safe surface. • 3) Check if any button was pushed down. In case any button is pushed down, you can't key in codes.

• • The LCD shows 'Open' but it turns into 'Lo-bat' and all letters disappear! • This happens when the wiring harness wasn't socketed properly. Please open the keypad and check the inside of the keypad. • • The LCD display shows the following error messages! • Err F: Check that the 'START' button has been pressed. • Err b: Check that the 'Memory' button has been pressed. • Err E, Err 1~9: Contact your nearest Eaglesafe dealer.

If you still have problem, please contact the nearest distributor. If you don't have any record, please contact info@eaglesafes.com to be connected to authorized eaglesafes' dealer.!

WARNINGS AND CAUTIONS 1. Be careful while moving the safe because it is heavy; improper handling may cause injury.

Be careful not to collide with the corners of the safe and also ensure that your fingers do not get caught In the door of the safe. Moving a heavy safe may damage floors or other surfaces.

The safe should be installed on a level location with good ventilation and no humidity. Never let children play around or with the safe.

How to Dial and Change Safe Combination Lock Part 001 Mr. Locksmith Training Video. For further information go to This information is typical of a Sargent & Greenleaf (S&G), Ilco, or LaGard safe Mechanical Group II Combination Locks. Combination Operating Instructions: To unlock the safe use the 'Opening Index' (located at the 12 o'clock position) on the dial ring for each number. You must dial the combination precisely without backing up.

- Left 4 or more turns to the left (counterclockwise) stopping at the first number '20' - 3 turns to the right to the 2nd number stopping at '40' - 2 turns to the left to the 3rd number stopping at '60' - Right to open: turn the dial to the right until it stops moving. There are a few safes out there that are R-L-R instead of L-R-L. In that case, you utilize the same procedure except that you would reverse the direction. Note: See upcoming videos on 'forbidden zone,' drop point, opening locked safes, combination lock maintenance, troubleshooting, safe tools and the most important tool to open a safe!

Visit my website for On-line and Hands-on Locksmith Training Dates and Cities near you for Beginners, Intermediate, Advanced Locksmithing as well as my Covert Methods of Entry, Non-destructive Methods of Entry and to purchase the Famous 'Dumb Key Force Tool' that opens Smart Key locks go to.