I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc.

We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us. Download Cs Go. We need to logon to different devices for troubleshooting/network managment which sometimes becomes very tough to us. So I wonder if there any cisco applications or tools by which we can centrally manage all these devices. If would be a great help for us if anyone can suggest.

Sep 21, 2004. Step 1 Install and start the Cisco EMF software. You must install a fully licensed version of the full Cisco EMF application before you can install the Cisco Catalyst Switch Manager software. For details, see the 'Installing the Cisco Element Manager Framework' section. Step 2 Check the Catalyst switch.

The closest low cost (free) Cisco product to manage most of that would be (CNA). It'll do fine with your switches and manage at least your 2900 series router. If I were on a budget I'd use CNA for the switches, add in (CCP) for the couple of routers and use the built-in browser-based interface for the WLC (which covers its WAPs as well). If you want a paid Cisco product to cover it all, you'd have to step up to Cisco Prime Infrastructure at the base licensing level (up to 50 devices). List price for that is about US$5295. Third party options abound and also range from free open source projects (Nagios, Cacti, RANCID etc.) to full-featured systems such as the SolarWinds products (NPM, NCM, etc.). The closest low cost (free) Cisco product to manage most of that would be (CNA).

It'll do fine with your switches and manage at least your 2900 series router. If I were on a budget I'd use CNA for the switches, add in (CCP) for the couple of routers and use the built-in browser-based interface for the WLC (which covers its WAPs as well). If you want a paid Cisco product to cover it all, you'd have to step up to Cisco Prime Infrastructure at the base licensing level (up to 50 devices). List price for that is about US$5295.

Third party options abound and also range from free open source projects (Nagios, Cacti, RANCID etc.) to full-featured systems such as the SolarWinds products (NPM, NCM, etc.).

Installing the Cisco Catalyst Switch Manager Table Of Contents Installing the Cisco Catalyst Switch Manager This chapter describes how to install the Cisco Catalyst Switch Manager, and contains the following sections: • • • • Cisco Catalyst Switch Manager Installation Workflow The following steps outline a typical workflow for installing the Cisco Catalyst Switch Manager: Step 1 Install and start the Cisco EMF software. You must install a fully licensed version of the full Cisco EMF application before you can install the Cisco Catalyst Switch Manager software. For details, see the. Step 2 Check the Catalyst switch hardware setup. For details, see the.

Step 3 (Optional) Mount a remote CD-ROM to install the Cisco Catalyst Switch Manager from a remote system. For details, see the. Step 4 Install the Cisco Catalyst Switch Manager software using the eminstall script. For details, see the. Step 5 (Optional) Set up the Cisco EMF server as a TFTP server.

Step 6 Deploy a Cisco Catalyst Switch Manager object into Cisco EMF. For more information, see the 'Getting Started' chapter in the Cisco Catalyst Switch Manager User Guide. Tip Check Cisco.com for details of the latest patch releases for the Cisco Catalyst Switch Manager application. For details, refer to the Preface under Cisco Catalyst Switch Manager Installation Prerequisites Prior to installing the Cisco Catalyst Switch Manager, you must before the following tasks: • • Installing the Cisco Element Manager Framework Version 3.2 of the Cisco Catalyst Switch Manager must be used with Cisco EMF version 3.2 service pack 7 and patch 7.1. You must install and run the appropriate Cisco EMF version before you can install the Cisco Catalyst Switch Manager. For more information, see the Cisco Element Management Framework Installation and Administration Guide.

Hardware Configuration Before you can use the Cisco Catalyst Switch Manager to manage a particular Catalyst switch, you must configure the device. It is suggested that you perform hardware configuration prior to installing the Cisco Catalyst Switch Manager. Depending on the software installed on the device, configure each device to be managed via the element manager according to the appropriate procedure, as follows: • • • • Configuration Procedures (Catalyst OS) These procedures are applicable only to switch instances running Catalyst OS only (no MSFC daughter card installed on the supervisor module). You must configure the following prerequisites before the Cisco Catalyst Switch Manager can manage a Catalyst switch: • • • • • To perform the procedures in this section, you must enter these commands through the console port on the supervisor engine of the Catalyst switch. Setting the Supervisor Enable (Privileged Mode) Password To set the supervisor enable password, follow these steps: Step 1 Type enable to enter the enable mode: switch>enable Enter password. John Mohegan Jazz Improvisation Pdf Free here.

Configuration Procedures (Hybrid OS) These procedures are applicable only to switch instances running Hybrid OS (Catalyst OS installed on the supervisor engine and IOS the MSFC). You must configure the following prerequisites before the Cisco Catalyst Switch Manager can manage a Catalyst switch. You must configure the following prerequisites before the Cisco Catalyst Switch Manager can manage a Catalyst switch: • • • • • • • • • • To perform the procedures in this section, you must enter these commands through the console port on the supervisor engine of the Catalyst switch. Setting the Supervisor Enable (Privileged Mode) Password To set the supervisor enable password, follow these steps: Step 1 Type enable to enter the enable mode: switch>enable Enter password. Tip If the session 15 command fails, the supervisor module either does not have an Multilayer Switching Feature Card installed or the MSFC boot image/configuration is damaged in some fashion. In this case, the switch is operating in pure Catalyst OS mode and none of the following configuration options are possible.

While the Cisco Catalyst Switch Manager will detect and partially manage a switch running Catalyst OS only, the full configuration capabilities of the EMS are not available in this mode. Consult the appropriate Catalyst Switch Configuration Guides for more information on installing the MSFC or configuring/recovering the MSFC boot information.

Step 2 Type enable to enter the enable mode: Router>enable. Configuration Procedures (Native IOS) You must configure the following prerequisites before the Cisco Catalyst Switch Manager can manage a Catalyst switch. These apply only to switch instances running Native IOS (IOS installed on both the supervisor engine and the MSFC). Unlike the Hybrid OS situation, the supervisor engine and MSFC in Native IOS share a common configuration. You must configure the following prerequisites before the Cisco Catalyst Switch Manager can manage a Catalyst switch: • • • • • To perform the procedures in this section, you must enter these commands through the console port on the supervisor engine of the Catalyst switch.

Setting the Enable Password To set the enable password, follow these steps: Step 1 Type enable to enter the enable mode: Router>enable. Mounting a Remote CD-ROM Drive To install software onto a system that does not have its own CD-ROM drive, you need to mount the CD on the remote system and then export the device to make it accessible over the network. To mount a remote CD-ROM drive, follow these steps: Step 1 Insert the Cisco Catalyst Switch Manager CD-ROM into the CD-ROM drive on the remote host. Step 2 Log in as superuser on the remote host.

Enter /usr/bin/ps -ef grep vold to verify that the volume manager is running. When the Volume Manager is running, you see a message similar to this one: root 591 1 0 Feb 26?

0:01 /usr/sbin/vold. Note The following procedure assumes that a valid Cisco EMF server is installed and running. Refer to the Cisco Element Management Framework Installation and Administration Guide for further details. To install the Cisco Catalyst Switch Manager using eminstall, follow these steps: Step 1 Ensure that the following installation prerequisites have been met on the system: • Cisco EMF 3.2 Service Pack 7 and Patch 7.1 successfully installed • Cisco EMF started on the server (cemf start command) • Cisco Catalyst Switch Manager Version 3.2 package has been download from Cisco's website or is available on CD-ROM. Which package do you wish to install? (Def:q) [?,q] You must install the server package (option 1) on the same host as the Cisco EMF server. If you are using Cisco EMF in the client/server mode, then you must install the client package (option 3) on each host running the Cisco EMF client.

Because the example shown in Step 4 is from a host where the Cisco EMF server package was installed, Option 3 indicates an error 'Incompatible type c,' which means that you cannot install the client package on this host. Options 2 or 4 are available only if you are upgrading a currently installed Cisco Catalyst Switch Manager to a newer version. See for more information. Step 5 Select the installation you require. The utility performs the appropriate installation. A confirmation prompt displays.

Step 6 Provide the appropriate confirmation for the selected installation option at the prompt. An entry of 'y' indicates yes and the installation process commences. An entry of 'n' indicates no and cancels the installation process. Note If a Cisco EMF session is currently running, the Cisco Catalyst Switch Manager installation process automatically closes all Cisco EMF windows. As installation of each package takes place, the following displays: Installation of was successful.

At the completion of the installation, the following displays: The option install ' installation option' was completed successfully. Step 7 When the installation is complete, exit the CD-ROM area as necessary by entering the following at the command prompt: cd /. Replace CEMF_ROOT with the name of the directory where Cisco EMF is installed. Step 10 Log on with your username and password in the displayed login window. Step 11 From the Cisco EMF Launchpad, select the Viewer application.

If the Cisco Catalyst Switch Manager was installed correctly, the Deployment sub-menu from a container in the Physical tree will contain a CSM/7600 item. The Cisco Catalyst Switch Manager is now ready to use. See the Cisco Catalyst Switch Manager User Guide for information on using the Cisco Catalyst Switch Manager features available. Posted: Tue Sep 21 04:22:48 PDT 2004 All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.